Diacell® CryoDAC-atto

The link to this product has been copied.

Micro-spectroscopy, Pmax = 20 GPa, Tmin = 1.6 K, WD = 11 mm, A = 40°

Diacell® CryoDAC Series

Specially engineered to fit seamlessly onto the sample holder of the attocube cryostats: attoDRY 1000, attoDRY 2100
The height of this DAC and the very short working distance ensure that the sample is located very close to the observing top window of the cryostat
The cell was originally designed for micro-Raman measurements, but it is also suitable for any other micro-spectroscopy technique
The Diacell® CryoDAC-atto has a numerical aperture of 0.34 and it enables electrical work via its side ports
Maximum pressures of up to above 20 GPa may be obtained with Diacell® CryoDAC- atto

SKU: A81500

For more info, quotation or call: Contact us

Description

The Diacell® CryoDAC-atto was originally designed for micro-Raman work in the attoDRY800 cryostat from attocube. However, this cell can also be used for other micro-spectroscopy techniques, such as imaging and high resolution photoluminescence under high pressure. Provisions have also been made to enable electrical work.

The Diacell® CryoDAC- atto has been engineered to fit seamlessly onto the sample mount of the attoDRY 800, attoDRY 1000, attoDRY 2100. For more information about this specific microscopy cryostat, please refer to attocube webpage.

The cell comes equipped with a pair of 2.50 mm diameter Diacell design diamond anvils.

The cell is supplied aligned and ready for use.

Specifications

Cell Material	High Strength Beryllium Copper Alloy
Anvil Support Plate	Beryllium Copper
Pressure Mechanism	Screw Drive with Belleville spring washers
Maximum Pressure	20 GPa
Temperature Range	1.6 K (DAC holder)
Top Angle	40°
Lateral Access	N/A
Heating	N/A
Cooling	Via attocube Cryostat
Interfacing Solution	attoCFM special holder (consult with attoCube)
DAC Diameter	37 mm
DAC Height	30 mm
Working Distance to Sample	11 mm
Numerical Aperture	0.34
DAC Weight	123 g

Maximum pressure is dependent upon the culet size of the anvils. Almax easyLab is committed to its policy of continuous improvement. Specifications may change without notice. easyLab and Diacell are registered trademarks of Almax easyLab.

Spares, Accessories and Options

Our diamond anvil cells are aligned and mechanically tested before leaving our factory on their way to your laboratory.

They also come supplied with the required basic tooling, including gasket blanks, to use them. All is contained in the transportation casing to move around laboratories easily.

Below you can find some of the accessories and spares you might also consider. If you cannot find what you need, please do not hesitate to contact our team.

	Diamond Anvils 2.5 mm Diacell® design diamond anvil, force fitted in BeCu rings for easy fitting in the CryoDAC-atto Product code: [P00131], [M50011]
	Gasket Blanks 5 mm diameter and 0.30mm thick BeCu gasket blanks Product code: [P00537]
	Ruby Powder Variable size ruby grains for pressure calibration Product code: [P00104]

FAQs

What is the maximum pressure I can achieve with the CryoDAC Atto and a given culet size?

Culet size (µm)	500	600	800	1000
Pmax (GPa) (*)	20	14	8	5

(*) The Pmax values are only indicative. The maximum pressure achievable with a DAC is influenced by many others experimental parameters, like the gasket characteristics (material, thickness and hole size) or the pressure transmitting medium.

Reviews

There are no reviews yet.

Be the first to review “Diacell® CryoDAC-atto”